Buyer guide6 min read

IP Ratings Explained: IP20 vs IP44 vs IP65 vs IP67 for Christmas Lights

The letter and two numbers on a string light decide whether it survives the season. Here is how to read them and where each rating belongs.

Most outdoor Christmas lighting failures are not LED failures. They are ingress failures: water reaching a connector, condensation inside a driver, or dust and grit abrading a seal until moisture finds a way in. The IP rating on the product is the specification that predicts this — and it is the specification buyers most often overlook.

How to read an IP rating

IP stands for Ingress Protection, followed by two digits. The first digit covers solids (dust, tools, fingers); the second covers liquids.

RatingSolidsLiquidsWhere it belongs
IP44Objects over 1 mmWater splashing from any directionSheltered porches, indoor façades, retail interiors
IP54Dust, limited ingressSplashingCovered outdoor positions, some interior fittings
IP65Dust tightWater jetsThe default for permanent outdoor installations
IP67Dust tightImmersion, 1 m for 30 minGround-level runs, flood zones, neon flex in wet detail
IP68Dust tightContinuous immersion to an agreed depthFountains and permanent underwater features

IP44 vs IP20: the indoor and outdoor line

IP44 means protected against solid objects over 1 mm and against water splashing from any direction - the minimum sensible rating for anything installed outdoors under cover. IP20 means protected against fingers and objects over 12 mm, with no water protection at all. It is the rating on most indoor decorative sets, on lightweight motif pieces and on display props built for interior atria.

So the IP44 vs IP20 question is really a siting question, not a quality question:

IP20IP44
WaterNone - dry locations onlySplashes from any direction
Typical productsIndoor motif pieces, interior tree lighting, display propsSheltered façades, porches, retail displays near entrances
OutdoorsNo, unless inside a sealed weatherproof enclosureOnly where an overhang or canopy keeps rain off directly
ConstructionOpen joints, no gasket, no pottingSealed connectors and potted or heat-shrink joints
Relative costLowestA little higher - the sealing is the cost

Short answer: IP44 is better than IP20 for anything that can get wet. IP20 is perfectly adequate - and often thinner, lighter and cheaper - for interior work. If a piece is going outdoors with no cover, neither is enough: specify IP65.

IP44 vs IP65: which one do you need?

Short answer: if the light is under a canopy or behind glass, IP44 is enough for a sheltered season. If rain reaches it driven by wind — rooflines, façades, poles, trees, car parks — you need IP65. IP44 keeps out splashes; only IP65 keeps out dust and resists water arriving at pressure.

  • IP44 = objects over 1 mm + splashing water. No dust protection, no pressure resistance.
  • IP65 = dust tight + low-pressure water jets from any direction. The default for permanent outdoor work.
  • Rule of thumb: if you cannot stand under it in a storm and stay dry, specify IP65.

IP44 and IP65 are the two ratings buyers most often compare, and they are usually treated as "acceptable" and "better" versions of the same protection. They are not the same protection. Both keep out splashing water; only IP65 also keeps out dust and survives water arriving under pressure - which is what wind-driven rain does to every roofline, pole and tree.

IP44IP65
SolidsObjects over 1 mm; dust can still enterDust tight - no dust ingress
WaterSplashing from any direction, no pressureLow-pressure jets from any direction
Wind-driven rainDefeats the seal over a seasonSurvives it, if the connectors are sealed too
Typical constructionGasket at the joint; driver compartment may be openPotted joints, sealed connectors, gasketed enclosure
Where it belongsCovered porch, canopy, interior behind glass, one season under an overhangOpen rooflines, façades, poles, trees, permanent installations
Relative costBaselineA few per cent more - the sealing is the cost

The test that settles it: ask how the water arrives. Splashes fall; rain in a winter storm is pushed sideways and upwards at pressure, and that pressure is what an IP44 gasket is not designed to resist. A light that is IP44 along the string but sealed with a push-fit connector at every joint is, in practice, an IP44 system with eight weak points - and the joint is where the water gets in, not the LED.

So which do you buy? It is a siting question, not a quality question. Under a canopy that keeps rain off directly, IP44 is a legitimate one-season choice. On anything exposed - gutters, parapets, trees, car park poles, the front of a shopping centre - specify IP65 and treat IP44 as the wrong specification rather than the cheap one. Where a single rating has to cover a whole scheme, buy IP65: the price difference is a small percentage of the installed cost, against a lift or a crane visit to replace a section in week four of a six-week season.

The same logic explains why a stored IP44 set fails in its second year: dust and grit collected in the warehouse abrade the seal while the box is in transit, and the protection that was measured on a new sample is no longer the protection on the site. Our outdoor string light range states both the IP rating and the connector type on every model card for exactly this reason.

Why IP44 products fail on exposed façades

IP44 is commonly quoted on curtain lights and icicle strings and on consumer-grade sets. It is a legitimate rating, and it is the right one for a sheltered installation. It becomes a problem when the same product is installed on a building façade with no overhang, where wind-driven rain arrives at pressure from below for three months. Water enters the connector, tracks along the conductor and appears at the driver — usually in week four of a six-week season.

The failure is rarely instant. That is what makes it expensive: the installation looks perfect on switch-on night and deteriorates afterwards, when fixing it means another crane or lift.

A per-zone specification approach

Treat the installation in zones rather than choosing one rating for the whole scheme:

  • Rooflines, cornices and sheltered bays — IP65 for permanent work; IP44 acceptable for a single season under an overhang.
  • Open façades, poles and trees — IP65 minimum, with sealed connectors on every joint.
  • Ground-level detail, plinths and walk-through floors — IP67, and cable routed so it is not standing in water. Our IP67 neon flex and rope light range is built for this position.
  • Fountains and water features — IP68 with a compliant low-voltage supply and the appropriate transformer protection.
  • Drivers and power supplies — enclosures rated at least IP65, positioned above the flood level and, ideally, indoors or in a service cabinet.

The connector is usually the weakest point

A string can be rated IP65 and still fail at the joint where two sets connect, because the rating typically applies to the sealed construction, not to a loosely pushed-together plug. Ask specifically about the connector:

  • Is it screw-lock or push-fit? Screw-lock connectors maintain compression over a season.
  • Is the joint rated IP65 when engaged? The un-mated plug end is not.
  • Are unused sockets and tail ends capped and sealed as supplied?
  • Is there a gasket or O-ring, and is the material UV-stable?

Our outdoor string light range shows the IP rating on every model card, and the connector type is confirmed on the datasheet — compare those two lines before you compare price.

Low voltage is a separate question

Moving from 230 V to 24 V reduces shock risk and often simplifies municipal approval, but it does not remove the need for ingress protection — a 24 V connector full of water still corrodes, and the driver feeding it is the component most likely to fail. Use a certified transformer with its own IP-rated enclosure, and size it with headroom so it is not running at its limit for six weeks.

Supply-chain consequences of a low IP rating

Ingress failures show up as returns, warranty claims and, in a public installation, the risk of an electrically unsafe joint in a space full of people. The cost difference between an IP44 and an IP65 version of a similar product is a small percentage of the installed cost, and it is almost always worth paying where the light is exposed. For a zone-by-zone list that goes up to IP68 — including driveways, in-grade uplights and fountains — see the IP65 vs IP67 vs IP68 rating list.

Not sure which rating your installation needs? Send photographs of the site, the mounting position and the local weather exposure, and we will recommend the rating per zone — and quote the version that will still be working at the end of the season.

Frequently asked questions

What does IP44 mean in plain English?
The first 4 means protected against solid objects larger than 1 mm, including tools and thick wires. The second 4 means protected against water splashing from any direction. It does not mean waterproof, and it does not allow immersion or directed jets.
Is IP44 better than IP20?
Yes, for any location that can get wet. IP20 has no water protection at all and is a dry-location rating; IP44 adds splash protection, so it is the entry rating for sheltered outdoor work. For exposed façades, poles and trees, use IP65 instead.
Is IP44 the same as IP65?
No. Both protect against splashes, but IP65 adds dust-tightness and resistance to water jets at pressure. IP44 relies on a light seal that wind-driven rain defeats over a season; IP65 uses gaskets, sealed connectors and potted joints.
IP44 or IP65 - which is the better buy?
IP65, whenever the light is exposed to wind-driven rain: rooflines, façades, poles, trees and car parks. IP44 is the better buy only where a canopy keeps rain off directly and the installation is short-term, because the price difference is a few per cent against the cost of a lift or crane visit to replace a failed section.
Should I choose IP44 or IP65 for a Christmas light installation?
Choose by position, not by price. IP44 is acceptable only where a canopy or overhang keeps rain off directly, and realistically for one season. For gutters, rooflines, façades, poles and trees - anywhere rain arrives driven by wind - specify IP65. If one rating must cover the whole scheme, buy IP65.
Can I use IP20 lights outdoors under a canopy?
Only if the product never sees rain, spray or heavy condensation - for example deep under a roof overhang, indoors behind glass, or inside a sealed enclosure. In practice a single windy storm reaches positions that looked protected on a dry day, so treat IP44 as the outdoor minimum and specify IP65 where it is exposed.
Which IP rating should I specify for a commercial Christmas installation?
IP65 for rooflines, façades, poles and trees; IP67 for ground-level detail and walk-through floors; IP68 for fountains and water features; IP44 only under an overhang or indoors; IP20 only in dry interiors.
Working on a project for the coming season?

Send your specification, quantities and destination market — our export team replies within 12 working hours with pricing, lead time and packing details.

Request a quotation
Next step

Keep reading

More sourcing and specification guides for commercial Christmas lighting buyers.