Most giant Christmas tree projects go wrong for the same reason: the buyer specifies a height and a picture, and lets the factory fill in everything else. The factory fills in what is cheapest to produce, the tree arrives, and the problems start — bald patches at eye level, a top that is dim from 50 metres away, a base that moves in wind, or a lighting load that trips the site's breaker the first cold night.
A 20-metre tree is not a scaled-up 6-metre tree. Above roughly 10 metres it becomes a steel structure with a lighting system attached, and it needs to be specified like one: geometry, branch density, light points, electrical load, foundation, wind resistance and shipping volume all have to be decided before the order is placed.
This guide gives the numbers we use when quoting giant trees from 10 m to 30 m, and ends with a specification sheet you can copy into your own RFQ.
1. Start with the three parameters that decide everything else
Before anyone talks about lights, three numbers have to be fixed:
- Finished height. Ground to the top of the topper — not the height of the frame. Say "16 m including a 1.2 m star" so there is no argument later.
- Viewing distance. A tree seen from a motorway 200 m away and a tree in a mall atrium seen from 8 m need different branch density and different light spacing.
- Location type. Indoor atrium, sheltered square, or exposed coastal plaza. This single answer decides the steel grade, the base design and whether guy wires are allowed.
If you send only those three, a competent factory can already quote a realistic range. If you send a photo from Pinterest and nothing else, you will get a price — just not for the tree you actually need.
2. Geometry: taper, base diameter and section count
Commercial trees are built to a height-to-base ratio, not to an absolute base size. The convention for public installations is roughly 2.5:1 to 3:1 — a 20 m tree has a base diameter of 6.7 m to 8 m.
| Finished height | Base diameter (2.5:1 – 3:1) | Typical sections | Typical planted weight |
|---|---|---|---|
| 10 m | 3.3 – 4.0 m | 3 – 4 | 250 – 400 kg |
| 15 m | 5.0 – 6.0 m | 4 – 5 | 500 – 800 kg |
| 20 m | 6.7 – 8.0 m | 5 – 6 | 900 – 1,400 kg |
| 25 m | 8.3 – 10.0 m | 6 – 7 | 1,400 – 2,000 kg |
| 30 m | 10.0 – 12.0 m | 7 – 9 | 2,000 – 3,000 kg |
The taper (how quickly the cone narrows) matters as much as the diameter. A fast taper looks fat at the bottom and needle-thin at the top; most municipal trees use a near-linear taper with a slightly fuller bottom third, because that is the part people walk past and photograph.
Section count is a shipping and install decision, not an aesthetic one: more sections means smaller crates and easier handling, but more joints to align and more assembly time on site. Ask for a section drawing — if the factory cannot produce one before you order, they are not building to a drawing.
2b. The same sizes in feet
Most North American briefs arrive in feet, and the two scales get mixed up in the RFQ — which is how a "30 foot tree" turns into a 30-metre quote. Use this table to translate before you specify, and always state the unit in writing:
| Height in feet | Height in metres | Base diameter (2.5:1 – 3:1) | Where it usually goes |
|---|---|---|---|
| 20 ft | 6 m | 2.0 – 2.4 m | Retail forecourt, small town square, mall entrance |
| 30 ft | 9 m | 3.0 – 3.6 m | City plaza, waterfront promenade, resort lobby |
| 40 ft | 12 m | 4.0 – 4.8 m | Town centre, shopping street, event venue |
| 50 ft | 15 m | 5.0 – 6.0 m | Landmark roundabout, municipal square |
| 60 ft | 18 m | 6.0 – 7.2 m | City landmark, stadium approach, festival site |
| 100 ft | 30 m | 10.0 – 12.0 m | Flagship installation visible from a motorway |
Two practical notes. First, the height is finished height including the topper — a "30 ft tree" with a 1.2 m star means a 7.8 m frame. Second, anything from about 20 ft upward is a steel structure rather than a decorated cone, so the size you pick also fixes the base plate, the section count and the crane time on site.
3. Branch density: the number that decides whether it looks expensive
Ask for branch tips per square metre of surface, not "full" or "premium". The tree's visible surface area is roughly 0.63 × height² (a cone with a 2.5:1 taper), so:
- 10 m tree → about 63 m² of surface
- 20 m tree → about 250 m²
- 30 m tree → about 565 m²
For public installations we typically specify 60 – 90 branch tips per m² at the visible lower two-thirds and slightly less at the top, where nobody gets close. That translates to roughly 4,000 – 6,000 tips on a 10 m tree and 15,000 – 22,000 on a 20 m tree.
The material mix matters too. A common and cost-effective build is a PVC needle outer layer over a PE moulded inner core: PE gives the dense, realistic silhouette at the base and mid-section, PVC fills the volume cheaply. Pure PE at 30 m height is possible but the weight and cost climb fast.
4. Light points: how many, how spaced, how controlled
Light density is what makes a giant tree read from a distance. Too few points and it looks like a wireframe at night; too many and you pay for transformers, cable and electricity forever.
Practical ranges for warm-white LED installations:
| Height | Light points | Approx. load @ 0.06 W/point | Spacing feel |
|---|---|---|---|
| 10 m | 8,000 – 14,000 | 0.5 – 0.85 kW | Dense, photogenic up close |
| 15 m | 15,000 – 25,000 | 0.9 – 1.5 kW | Balanced |
| 20 m | 25,000 – 40,000 | 1.5 – 2.4 kW | Reads well at 100 m |
| 25 m | 40,000 – 60,000 | 2.4 – 3.6 kW | Landmark |
| 30 m | 55,000 – 85,000 | 3.3 – 5.1 kW | City-scale landmark |
Three specification details decide whether those numbers survive contact with reality:
- Even distribution, not even totals. A tree with 30,000 points clustered in the bottom half photographs badly. Ask for the points-per-section breakdown in the drawing.
- Voltage and drivers. 24 V DC strings with remote drivers keep mains voltage out of the tree body — safer in wet weather and easier to service.
- Control. Static warm white is the default. If you want animation, colour change or a music-synced show, say so at quotation stage: it changes the controller count, the channel layout and often the cable gauge. DMX pixel control on a 20 m tree is a different build, not an upgrade you add later.
Every string should be individually fused or protected, and the whole tree should have a single labelled disconnect point at the base. That one detail saves an hour every time a section needs service.
5. Structure: base, guys and wind load
This is where giant tree projects actually fail. The tree is a tall, light, high-drag object; the wind load at the top of a 20 m cone in an exposed square can be measured in tonnes of overturning moment.
- Frame. Galvanised steel centre pole with welded or bolted ring frames; powder-coated if the tree is coastal or permanent.
- Base. Either a weighted steel cross-base with ballast (for temporary installs on paving) or a chemical-anchored plate (for permanent sites). The factory should tell you the required ballast weight, not just supply a base.
- Guy wires. Above about 12 m in an open location, expect 4 – 6 guys at 45° to ground anchors. Municipal clients often refuse guys because they obstruct pedestrians — if that is your site, the base and pole have to be engineered for full cantilever load, and the price is different.
- Wind design. Ask which wind speed the structure is designed to. "It's strong" is not an answer. A design statement for the local wind code is.
For an indoor atrium tree the structural conversation is much simpler — but check the floor point load with the building manager before you order 1.4 tonnes of tree plus ballast.
6. Electrical supply and the site interface
The tree is one part of the electrical system; the site is the other. Specify the interface explicitly:
- Total connected load, plus 20% headroom for the topper, controllers and any additional lighting.
- Supply arrangement: how many circuits, what breaker rating, where the distribution board sits relative to the base.
- Protection: RCD/GFCI protection at the origin, IP65 enclosures for all outdoor connections, cable routed inside the frame rather than zip-tied to the outside.
- Compliance: CE and RoHS declarations for the assembly, and UL/ETL-listed components where the destination market requires them. Ask for the certificate numbers and check they cover the actual components used — a listing for a driver does not cover the whole tree.
If the tree will stand for more than one season, ask for the IP rating of every connector, not just the lights. Connectors are what fail first.
7. Packing and shipping volume
Giant trees ship as crates of frame sections plus cartons of branches and lights. A realistic budgeting figure is 0.8 – 1.2 m³ per metre of tree height:
| Height | Typical volume | Container plan |
|---|---|---|
| 10 m | 8 – 12 m³ | LCL, or shared 20 ft |
| 15 m | 12 – 18 m³ | 20 ft (33 m³) with room to spare |
| 20 m | 16 – 24 m³ | 20 ft, or 40 ft for multi-site orders |
| 30 m | 24 – 36 m³ | 40 ft, sometimes more with ballast |
Ask for the packing list by section, numbered to match the assembly drawing. On a 30 m tree with nine sections, mismatched numbering turns a two-day install into a four-day one.
8. Installation: time, crew, crane
Budget for site time honestly, because install cost often surprises buyers more than the tree itself:
- 10 – 12 m: 3 – 4 people, no crane, 1 day.
- 15 – 20 m: 4 – 6 people plus a 12 – 25 t crane, 2 – 3 days including lighting checks.
- 25 – 30 m: 6 – 8 people plus a 25 – 50 t crane, 4 – 7 days, weather-dependent.
Add a night commissioning session. Lighting faults are far easier to find against darkness than daylight, and it is the last chance to correct a section before the switch-on event.
9. The specification sheet to send with your RFQ
Copy this into your enquiry and any credible factory will quote to the same baseline:
| Item | What to state |
|---|---|
| Finished height | m, including topper |
| Base diameter or H:D ratio | e.g. 20 m / 7.5 m base |
| Location type | indoor atrium / sheltered square / exposed plaza |
| Wind design | design wind speed or local code reference |
| Branch density | tips per m², and PE/PVC mix |
| Light points | total, plus per-section breakdown |
| Light colour / CCT | e.g. 2700 K warm white |
| Control | static / multi-function / DMX pixel |
| Topper | star or ball, height, lit or unlit |
| Base type | ballast base / anchored plate, and required ballast |
| Compliance | CE, RoHS, UL/ETL-listed components |
| Deliverables | assembly drawing, packing list by section, wiring diagram, test report |
10. Five mistakes that show up in almost every failed giant tree
- Specifying height only. The base diameter, taper and section count are what you actually see in photos — and what you pay for.
- Buying light points as a total. Distribution per section matters more than the total, and it is free to specify.
- Ignoring ballast. The factory ships a base; the site has to hold the tree down. Ask for the required ballast weight in writing.
- Adding DMX after quotation. Pixel control changes controllers, channels and cable — it is a different build, and retrofitting costs more than ordering it.
- No numbered packing list. Nine sections, one crane, no numbering: that is a lost day on site for no reason.
Where to go next
Our giant commercial Christmas tree range covers 6 m to 30 m, built to a drawing with a section-by-section light plan. If your project is smaller or freestanding LED trees suit the site better, the commercial and artificial tree range and the LED trees cover atrium and streetscape work.
Three companion guides are worth reading before you place an order: MOQ and lead time for custom projects — because giant trees are always custom — IP ratings explained, which decides how the tree survives its first winter, and power load and transformer sizing, which decides whether the lighting plan is buildable. If certification is on your checklist, UL, CE, RoHS and UKCA explained covers what actually applies to a lit installation.
Send the filled specification sheet to our export team with the destination city and switch-on date. We reply within 12 working hours with a drawing, a price range and a shipping window — usually the same day.
