A motif looks like the simplest product in this industry: a snowflake, a star, a reindeer, some lights on a frame. It is actually the hardest thing to buy well, because everything that goes wrong is invisible in a photograph — a frame that distorts when it is lifted, an outline that goes muddy at 60 metres, a joint that fills with water in November, a section that does not fit through the mall's goods lift at 2 a.m. on installation night.
This guide is written for the two buyers who order motifs in volume: shopping centre management running a themed campaign on a retail calendar, and city or municipal teams decorating a street, square or gateway. The specification questions are the same; the priorities are not, and the difference is worth stating up front.
1. First, agree what "motif" means in your order
The word is used for at least four different products, and half of all quotation arguments start here.
| Product | What it is | Typical use |
|---|---|---|
| 2D motif | Flat frame with a lit outline or filled areas; single viewing plane | Façades, walls, fences, pole brackets, windows |
| 3D motif | Freestanding or suspended volume frame, lit from more than one plane | Plazas, atriums, entrances, photo points |
| Pole decoration | Motif plus a clamp or bracket engineered for a specific post diameter | Street and car park lighting columns |
| Sculpture | Structural armature carrying a sculpted skin or dense light wrap | Landmark pieces, walk-through features |
Our 3D & motif range is built around the first three; the structural end of the fourth sits in light sculptures. If your brief mixes them — a 2D logo on the façade, a 3D piece in the atrium, pole motifs down the street — specify and price them as separate lines even when one supplier makes all three, because their engineering constraints are not the same.
2. The construction decides how it looks in week six
Three materials do almost all of the work, and each is visible from the ground:
- Frame. 16 mm steel rod, welded and then electrostatic powder-coated. Rod diameter is the difference between a shape that stays true and one that sags in the middle of a 5 m span. Anything above roughly 3 m needs internal bracing, and above 5 m it needs a sectioned frame with keyed joints rather than one continuous outline.
- Light source. Neon flex gives a continuous, crisp outline — the right choice for logos, letterforms and clean geometry. 5 mm concave LEDs give fine detail and fill, and are what makes an animal or a character read as a shape rather than a blob. Mixed construction, flex for the outline plus concave for the interior, is what most good pieces actually use.
- Sealing. Outdoor motifs are only as good as their joints. Epoxy-sealed LED modules and IP65 screw-lock connectors, rated from -20 °C to +45 °C, are the working specification for anything that stays outside through a winter.
The single most common build failure is a frame that was welded flat and then lifted by two people at the ends: it twists, the outline no longer matches the drawing, and no amount of re-hanging fixes it. Ask how the piece is lifted and whether the frame was designed for that lift point.
3. Size it from the viewing distance, not from the catalogue
A motif is sized by where people will stand, not by what fits the budget. The rule of thumb we quote with: a lit outline stays readable at roughly 25–30 times its own height, assuming a clear line of sight and no competing light.
| Motif height / diameter | Reads clearly from | Where it belongs |
|---|---|---|
| 0.5 – 1 m | 15 – 30 m | Shopfronts, entrances, window and shelf displays, indoor accents |
| 1 – 2 m | 30 – 60 m | Pole brackets, façade fascia, low-level plaza pieces |
| 2.5 – 3 m | 70 – 90 m | Atrium centrepieces, plaza and roundabout features |
| 5 m | 125 – 150 m | Street-wide landmarks, gateway and junction pieces |
| 8 – 10 m | 200 – 300 m | Tower façades, motorway approaches, city gateways |
Two consequences buyers underestimate. First, undersizing is the expensive mistake: a 1.5 m motif on a 40 m-wide plaza is invisible, and no lighting upgrade rescues it. Second, density has to scale with size — the same light spacing that looks rich on a 1 m snowflake looks sparse on an 8 m one. When you compare quotes for a large piece, compare light points per square metre, not total light points.
4. Mounting: the part that decides whether it survives wind
Street and pole work lives in the harshest conditions the industry builds for: wind funnelling between buildings, vibration from traffic, salt and grit spray, and crews working at height in the dark. Three mounting families cover most schemes:
- Pole clamps. Universal clamps suit posts from roughly Ø 60 mm to Ø 200 mm without drilling — which matters, because drilling a lighting column usually voids its own certification. Ask for the clamp range and whether a shim kit is included for tapered posts.
- Catenary spans. Cross-street spans need the span length, the attachment height on each side and the local wind zone before anyone can price them. The wire, the tensioning method and the drop cables are all separate lines.
- Suspended atrium pieces. Mall and void installations hang from structure, not from the ceiling finish. You need the structural anchor points, a secondary safety bond independent of the main suspension, and a rigging plan that an on-site contractor will accept.
Wind load is not a detail you can leave to the factory guessing. Tell them the site, the mounting height and the local wind zone; a competent supplier returns a frame calculation with the quotation. A supplier who answers "it is strong" has not calculated anything. Our street and pole range is specified this way as standard, and the quoting sequence is set out in the street pole quotation guide.
5. Power and control, sized before the order
Motifs are usually 24 V for safety and easier dimming, with 230 V available where a scheme is large and long cable runs would otherwise lose voltage. Three numbers have to be on the drawing:
- Load per piece, in watts, at the specified voltage.
- Driver capacity, sized at no more than about 80% of rated output — the reserve is for cold-start inrush and for the tolerance between one batch of LEDs and the next.
- Circuit grouping: which pieces share a driver and a switch-on circuit. A scheme where every motif has its own driver is a scheme with forty failure points and no way to switch it on as one display.
For animation or colour change, decide early whether control is DMX/Art-Net, a standalone SD-card show, or a simple RGB controller — the answer changes the wiring, the connector count and the price. Mixed schemes are normal: static warm-white outlines with one animated centrepiece reads better than everything moving. The maths for drivers and voltage drop is in our power load and transformer sizing guide.
6. What shopping malls ask that cities do not
Retail campaigns are judged on three things beyond the design: whether the install fits the overnight window, whether the display still looks intact after six weeks of footfall, and whether it photographs well enough to earn free reach.
- Fit the lift, not just the atrium. Section sizes are set by the goods lift and the service door, not by the piece. Give the supplier those dimensions with the brief; a 3 m ring that arrives as one welded unit and does not fit the lift becomes a very expensive conversation at 2 a.m.
- Build for touching. Atrium pieces get leaned on, sat on and climbed through. Specify mechanical fixings rather than adhesive for anything at hand height, and anti-slip bases on walk-through floors.
- Design one photo point. A single piece sized and lit for phone cameras — front-lit, at eye height, with a clear background — earns more impressions than three that photograph as glare. This is the logic behind our mall installation packages.
7. What cities ask that malls do not
Municipal schemes are corridors, not rooms, and they are judged as a whole from the end of the street.
- Visual consistency beats individual brilliance. One strong pole motif repeated down twelve poles reads better than twelve different ones. Fix the motif, the colour temperature and the mounting height, then repeat.
- One switch-on schedule. The avenue should light as one display, which means a control plan across the whole scheme, not per pole.
- Spares by pole type. Two percent spares are useless if the failed piece is the only 5 m gateway motif in the city. Specify spares per model, including the pieces that cannot be bought locally.
8. From artwork to approved sample
Custom shapes are the normal case, not the exception, and the process is quick if the artwork arrives in the right form.
- Send vector artwork (AI, EPS or PDF), or a clean high-resolution photo for redraw. Raster logos get traced, and traced logos lose the detail that made them recognisable.
- State minimum stroke width. Thin strokes cannot be built in neon flex; below roughly 20–25 mm the outline has to become a concave-LED line instead. Better to agree that on the drawing than to discover it in the sample.
- Get a render first, then a physical sample. A 3D render is a design conversation; the sample is the engineering one. We typically return a render quickly and a physical sample in around 7 days on approved geometry.
- Approve and seal it. The sealed sample is the acceptance reference for the production run — this is the clause that prevents a colour argument in October.
9. Packing: the constraint nobody puts on the drawing
Large motifs travel as sections, and the shipping envelope is fixed by the container door. Our working limits for a single packed piece are height 2.2 m, width 2.25 m and length 5.8 m; anything larger is designed in modular sections with keyed joints and assembled on site.
So the specification sheet needs three lines that buyers often leave blank: the longest single section, the weight of the heaviest section, and the assembly method — bolted keyed joints, spigot connectors, or lift-assist. Add the crate dimensions and total CBM, and the freight quote stops being a guess. A 10 m landmark piece built as three sections is not a compromise; it is the only version that can be shipped, lifted and stored.
10. The RFQ checklist
| Item | What to state |
|---|---|
| Type | 2D motif / 3D motif / pole decoration / sculpture |
| Size | Height or diameter, and the viewing distance it must read from |
| Construction | Frame rod diameter, coating colour, neon flex vs concave LED |
| Light | Colour temperature, single colour or RGB, animation yes/no and control protocol |
| Mounting | Pole diameter and clamp type, span length, wall bracket or suspension, wind zone |
| Electrical | Voltage, driver location, switch-on grouping, plug standard |
| Environment | Indoor / sheltered / exposed; minimum temperature; salt exposure |
| Compliance | Destination market and the marks you need on paper |
| Packing | Lift and door dimensions, longest acceptable section, crate limits |
| Quantities | Per model and colour, plus spares per model |
Send that list with your artwork and a site photo, and a motif quotation becomes a specification rather than a number. If you are still choosing between motif types for a scheme, the mall lighting planning guide covers how the pieces work together as a campaign. Send your brief and we will come back with a per-piece specification, packing plan and quotation — usually within 12 working hours.
